UK supplied · Research use only

LABORATORY GUIDE

Peptide purity testing: what HPLC and mass spectrometry actually measure

Published 27 October 2026 · 8 min read · View as Markdown

AT A GLANCE

HPLC purity measures what share of detected material is the target peptide; it says nothing about identity, water, salt or fill. Mass spectrometry confirms identity against the theoretical molecular weight. Purity is not content: a 99% pure vial can be under-filled. Check the chromatogram, and match the batch number to your vial.

Purity is the most quoted number in peptide supply and the most misunderstood. It answers a narrow question, how much of the detectable material is the target molecule, and it says nothing about identity, quantity or sterility on its own. Understanding what the methods do and do not show is what lets you read a report properly.

Two methods, two different questions

Purity and identity are separate questions and need separate methods. HPLC answers the first. Mass spectrometry answers the second. A report carrying only one of them is only half a report.

How HPLC works

High-performance liquid chromatography pushes the sample through a packed column under pressure. Different components travel at different speeds depending on how they interact with the stationary phase and the mobile phase, so they elute at different times and are detected separately, usually by UV absorbance. The output is a chromatogram: a baseline with peaks on it.

Purity is calculated as the area under the main peak divided by the total area under all peaks, expressed as a percentage. A 98% figure means 98% of the UV-absorbing material that came off the column was the target peptide. The remaining 2% is other UV-absorbing material: truncated sequences, deletion peptides, oxidised variants, diastereomers.

What a chromatogram tells you that a number cannot

  • Whether the main peak is sharp and symmetrical, or broad and tailing
  • Whether impurities elute close to the main peak, which makes the separation harder and the number less meaningful
  • Whether the baseline is flat or noisy
  • Whether the peak shape is consistent with a single species

A purity figure with no chromatogram attached cannot be checked at all. The chromatogram is the evidence; the percentage is a summary of it.

How mass spectrometry works

Mass spectrometry ionises the sample and measures the mass to charge ratio of the ions, which gives the molecular mass of the molecule. Comparing that against the theoretical mass for the sequence confirms the compound is what the label says. For retatrutide the theoretical value is about 4,731 Da and for BPC-157 about 1,419 Da. A result within a fraction of a dalton of the theoretical figure is confirmation. A result tens of daltons away is a different molecule.

Purity is not content

Purity is a percentage of what the detector saw. It is blind to water, residual salts, counter-ions and solvent, none of which absorb at the wavelengths used. A vial can be 99% pure and still contain well under the labelled amount of peptide if it holds 20% water and salt by weight. That is why net peptide content is reported separately, and why a certificate without a content figure does not establish the fill.

QuestionMethodWhat it establishes
Is it the right molecule?Mass spectrometryIdentity against theoretical mass
How much else is in it?HPLCPurity as a percentage of detected material
How much peptide is in the vial?Net peptide contentFill, after water and salt
Is it sterile?Not established by eitherNothing, unless tested separately

What neither method catches

  • Water and salt content, which only a content assay addresses
  • Sterility and endotoxin, which need separate microbiology
  • Residual solvents from synthesis, which need gas chromatography
  • Whether the material was handled cleanly after testing
  • Whether the vial you were sent came from the batch that was tested

The last point is the one buyers can control. Matching the batch number on your vial to the batch number on the report is the step that connects the laboratory result to the object in your hand. Without that match, a genuine report proves only that some material, somewhere, was tested.

Reading a report in order

  1. Laboratory name and report number, so the result is traceable to a source
  2. Batch number, checked against your vial
  3. Compound and labelled strength
  4. Mass spectrometry result against the theoretical mass
  5. HPLC purity with the chromatogram, and a look at the peak shape
  6. Net peptide content, if the fill matters to your work
  7. Test date, to confirm the report belongs to the current batch
Every Vyrax Labs batch certificate is published on the Lab Reports page and can be looked up by the batch number printed on the vial. Products are sold as research compounds.
This guide covers general peptide chemistry. Vyrax Labs products are sold as research compounds, and nothing here is medical advice.

Compounds in this guide

More guides